If you're exploring the best way to build a retaining wall in your backyard, you're likely weighing the pros and cons of treated lumber versus segmental block systems like Belgard. At The Ultimate Deck Shop, where our customers range from weekend warriors to landscape contractors across Saskatchewan, we've seen both solutions used in every condition Canadian weather can throw at them. Let’s break down cost, lifespan, building code requirements, and share the kind of hard-earned advice you usually only get from seasoned pros—right here for you.
Cost Comparison: Treated Lumber vs Segmental Block
The up-front outlay is often the deciding factor for many DIYers and even some pros. Here’s how it usually shakes out for a typical backyard project in the prairies, based on 4-foot-high, 20-foot-long walls:
| Factor | Treated Lumber | Segmental Block (e.g., Belgard Tandem Wall) |
|---|---|---|
| Materials per sq ft | $15–30 (6x6 PT timbers, hardware, gravel) | $25–50 (interlocking block, geogrid, base gravel) |
| DIY Equipment Costs | $0–500 | $500–1,500 (plate compactor, levels) |
| Professional Install (per sq ft) | $20–50 | $40–80 |
| Annual Maintenance | $100–300 (sealing, staining) | $50–100 (minor cleaning only) |
For shallow walls under 4 feet, treated lumber gives you the best bang for your buck up front if you’re handy and don’t mind the maintenance. Segmental block comes with higher material and install costs, but reduces your future maintenance workload significantly.
Longevity in Prairie Climate: What Actually Lasts?
Retaining walls in Saskatchewan and Alberta face dramatic freeze–thaw cycles. Select your materials accordingly:
- Treated Lumber Retaining Walls—Depending on grade and drainage, plan for 10–40 years. Above-ground sections may last around 20 years, but when lumber contacts moist soil with inadequate sealing, the clock ticks much faster. You can extend life with regular applications of products like Cutek Extreme and smart use of impermeable flashing or membrane barriers.
- Segmental Block Walls—With proper gravel base, drainage pipe, and geogrid reinforcement, blocks like Belgard Tandem Wall can easily outlast pressure-treated timber by two to five times, with many lasting 50 years or more.
Tip: Both wall types require effective drainage. Most early failures result from trapped water and frost. For timber, insist on a 12-in gravel backfill with a drainage pipe and use a quality sealant. For block, take time to compact the base, use geogrid over 4 ft, and check wall straightness often.
Building Code and Permit Considerations
Skirting code and permits may seem tempting, but Saskatchewan municipalities are strict—especially if you’re over 2 ft (about 0.6 m) in height.
- Heights under 4 ft (1.2 m): DIY is permitted without an engineer, especially with wood. Still, you should check city requirements. Anything over this needs engineering, especially for segmental block walls.
- Proper Drainage: Building codes require 12-inch gravel and a perforated drain pipe behind all walls. This prevents hydrostatic pressure, which causes most collapses.
- Foundation Depth: Both materials require frost protection, especially in prairie cities where frost lines are deep (Regina/Saskatoon often require 48 inches below grade for stability).
- Setbacks: Retaining walls can’t be too close to structures or property lines—usually a distance of at least 1 m is required.
- Permits: Permits are almost always required for anything above 2 ft in height or supporting a surcharge (like a patio or driveway behind the wall). Always check with your local municipality or the National Building Code of Canada section 9.20.
If you want expert help with a fully to-code wall with 3D design, our team can guide you or your contractor on the details.
5-Step DIY Guide: How We Approach a Treated Lumber Wall (Up to 4 Feet)
- Plan & Get Permits: Lay out the wall, mark utilities (always call before you dig!), and confirm with your city about permits and setbacks.
- Excavate: Dig a trench at least 6 inches below grade, and at least 24 inches wide for base stability. Add and compact 6 inches of 3/4" minus gravel.
- Base Course Install: Set your first row of 6x6 pressure-treated timbers, ensuring level. Use 12-inch galvanized spikes to lock timbers together. For best rot resistance, coat end grains and ground contact sides with a water-repellent wood oil or membrane.
- Backfill & Drainage: Place a 4-inch perforated drain pipe behind the first course. Backfill with at least 12 inches of clean, washed gravel—wrap pipe in geotextile fabric to prevent clogging.
- Stack and Secure: Stagger joints, spike or use timberlocks between every layer. Cap with a wider board for a clean look and additional protection, and seal everything exposed with exterior oil or stain. Integrate landscaping or even pergolas and shade structures for additional function or style.
For a more detailed breakdown of wood vs composite choices (especially if you’re building a deck at the same time), you may like our internal post on composite wood vs real wood.
5-Step DIY Guide (Advanced): Segmental Block Retaining Wall
- Layout and Permits: Plan wall shape, length, and measure slope accurately using a laser level or string line. Get all necessary permits and confirm block specs.
- Excavation and Base: Dig at least 12 inches below finished grade, wider than final wall by 6–8 inches each side. Place and compact a minimum 6-inch base of 3/4" gravel.
- First Course and Leveling: Lay the first block row. Meticulous leveling is key for strength and clean lines. Each block should be checked individually.
- Add Courses and Geogrid: Stack subsequent rows, staggering seams. For walls over 3–4 feet, embed geogrid into the compacted backfill every few courses per manufacturer specs.
- Drainage and Backfill: Backfill as you build with clear gravel (not soil) for at least 12 inches behind the wall. Place perforated drain pipe at base, daylighting out at an angle.
The attention to base and drainage is what truly separates a wall that lasts decades from one that heaves or cracks. If you’re curious about the details for wall systems, we cover installation tips on Belgard Ashlar Tandem Walls in another blog.
Quick Visual: When Should You Use Each?
| Treated Lumber | Segmental Block | |
|---|---|---|
| Ideal For | Budget projects, short walls, rustic/woodland style | Premium/stylish looks, tall/structural walls, low maintenance |
| Common Height | Up to 4 feet | Up to and beyond 10 feet (engineered) |
| Ease of DIY | Very DIY-friendly | Moderate (requires more tools, skill, time) |
| Main Drawback | Needs upkeep, eventual rot in contact zones | Higher upfront cost, heavier lifting |
| Best Code Compliance | Simple for low walls | Must be engineered for anything tall |
Maintenance: What Homeowners Should Expect
A treated lumber wall isn't fire and forget. The biggest complaints we hear after a decade or more come from rot at the base, splitting, and brushing off fungus or moss. Here’s what we advise our local customers:
- Re-treat exposed wood every one to two years with a good oil or sealer. Never skip the end grains or fastener points.
- Check for shifting or frost heave in early spring—tighten spikes or add extra support before minor problems become major.
Concrete block? Virtually maintenance free except for weeding, the occasional clean with a garden hose, and rare joint repairs after decades.
Code and Safety Tips: Stay on the Right Side of Inspectors
- Never backfill block or timber wall with soil—it settles and traps water, leading to bulges or collapse.
- Walls above 4 ft? Get them engineered, and never try to cut corners with geogrid or reinforcement details.
- Always call for utility locates before digging. In Saskatchewan, start with Sask 1st Call for peace of mind and legal compliance.
- For mixed-use yards (like a retaining wall supporting a patio, pergola, or heavy landscaping), factor the additional weight into your design.
We cover deck code requirements in more depth in our internal post on modern code and materials for decks.
Incorporating Shade and Functional Design Features
Many customers want more than just a wall—they want a functional outdoor living area. This is where segmental blocks excel, especially when you add integrated seating, garden beds, or connect the space to a pergola or shade structure. See our guide on Pergolas & Shade Structures for inspiration and check how your wall design can flow into multi-use spaces.
Our Bottom Line & Honest Advice
Here’s what we tell friends and neighbors, not just customers. Use treated lumber for short, simple, lower-cost applications—just know you’re signing up for regular maintenance and, eventually, replacement. If you want a permanent, low-maintenance solution or need height and structure, segmental block is worth the higher initial price. Either way, pay close attention to drainage and code.
If you’d like expert help, or want to see current pricing, textures, and block colors in person, come visit us in Regina or Saskatoon. We’ll give you straight answers, help you design a wall that’ll stand the test of time, and offer tool rentals if you want to DIY but don’t own every piece of gear yet. Canada-wide shipping is available. If you’re just starting the planning phase, grab a free quote or book a one-on-one consult—no pressure, just clarity.
Looking to make your backyard truly multi-season? Explore how hardscape walls integrate with covered spaces and browse the Pergolas & Shade Structures pillar page for inspiration and practical project tips.
